Install support when you plant, choose a cage for compact types and a stake or trellis for vining types, and tie stems loosely as they grow. A leaning plant can usually be straightened if you act early, while the stem is still flexible.
Why support matters
Support keeps the plant upright and the fruit off the soil. Fruit that rests on soil is more likely to rot and attract pests, and a well-supported plant is easier to check and harvest. Support also keeps the stem from bending or breaking under the weight of a heavy crop.
Choose a support
Cages
Cages suit determinate (bush) varieties and other compact plants. Choose one that is at least about 3 feet tall and fits the bed or pot. A cage that’s too short for the variety will let the plant grow out the top and fall over.
Stakes and single-stem supports
A single tall, sturdy stake suits a vining variety that you have pruned to one stem. Drive the stake in at planting, and tie the stem to it as it grows.
Tripods and teepees
Three or four poles tied at the top make a tripod or teepee. These suit pots and small beds, and they hold a vining plant well without much room.
Trellises and string
A-frames, mesh panels, wire, or a single overhead string with a vertical line for each plant suit vining tomatoes, especially in tight spaces. Trellises keep plants in a narrow line and make harvest easier.
Install support at planting
Push stakes, cages or trellis posts into the soil when you plant. Installing them later can damage the roots, which spread quickly through the season. For cages, push the legs at least 6 inches into the soil so the cage stays upright.
Tie stems loosely
Tie the main stem to the support with soft twine, cloth strips or plant clips. Tie loosely so the stem can thicken without being squeezed. A figure-eight loop, with a gap between the twine and the stem, works well. Check the ties every week or two, and retie any that have slipped or tightened.
Supporting tomatoes in pots
Pots tip more easily than beds, especially when the plant gets heavy with fruit. To keep a potted plant upright:
- Install the support at planting: a cage, stake or tripod set into the potting mix.
- Weight the base: add a heavy layer of stones or a weight at the bottom of the pot, or use a heavier container.
- Shelter the pot: set it against a wall or fence to block wind.
- Size the pot: a larger container holds the plant more stably. For pot size and watering, see how to grow and care for tomato plants.
Fixing a crooked or leaning plant
Plants lean for a few common reasons: a weak, leggy seedling; no support, so the stem flops; heavy fruit on one side; strong one-sided light; wind; or a crowded pot.
To straighten a plant:
- Act early. A young stem bends easily. A thick, woody stem can snap if you force it.
- Add a stake a few inches from the stem, not through the roots.
- Tie the stem gently to the stake so it grows upright. Retie as the plant grows.
- Move the plant toward more even light if one side of it leans toward a window or the sun.
- Bury more stem at the next planting if the seedling is tall and thin. The buried stem roots, which helps the plant stand up. See how deep to plant tomatoes.
A plant that leans badly after it has set a lot of fruit is hard to straighten. In that case, support the whole plant, and don’t try to bend it back.
Common mistakes
- Installing support late: you can damage roots when you push a stake in beside an established plant.
- Tying too tight: the stem can be squeezed or cut as it thickens.
- Choosing a cage too short: the plant grows out the top and collapses.
- Using a cage on a tall vining type: a vine can outgrow a cage. Use a stake or trellis instead.
- Leaving a pot unanchored: a top-heavy pot can tip in wind.
For spacing that fits your support choice, see how far apart to plant tomatoes. If you’re training a plant to a single stem, see pinching out tomato side shoots.